Steering Spindle
 |
 VINTAGE ALLIS B TRACTOR STEERING SPINDLE ARMS TIE ROD  US $39.99
|
 MASSEY FERGUSON MF 50 LEFT SPINDLE STEERING ARM US $28.00
|
 ORIGINAL MASSEY HARRIS 30 TRACTOR STEERING SPINDLE GEAR 1950 US $49.99
|
 VINTAGE JI CASE TRACTOR STEERING SPINDLE GEAR US $34.99
|
 power steering Spindle Vane bracket 720 730 520 620 US $20.00
|
 VINTAGE JI CASE TRACTOR STEERING SPINDLE ARM DRAG LINK US $49.99
|
Intrepid Brake caliper bolt stripped.. Is this safe?
Alright I have a 99 intrepid and I was doing brakes and the brake caliper bolt hole stripped out. And if you have ever owned a intrepid you would know that the whole steering spindle knuckle has to be replaced. So I could either use heli-coil for it as others have suggested and I have no experience in doing these. Or like I did is went to the hardware store and bought a locking nut that fits a 8x1.25 bolt. I cannot get my fingers or a wrench in the inner part of the caliper when I put it on so I glued the nut on the inside so id be able to get the bolt in it and was able to stick a flat head in and hold the Nut to tighten. The bolt does go far enough perfectly to hit the nylon in the lock nut and I would guess it is tightened to 60-80 pounds. Its real tight but do you think this is safe? Do you think the bolt could loosen in a locknut?
I wouldn't exactly call it safe but I don't think it is dangerous. The force is sideways on the bolt so as long as the bolt doesn't loosen up there shouldn't be a problem. If I were in that situation I would check it in a few days, then in a week or so after that if it is tight, then a month or two later. If it is hanging in there the annual brake pad checks should be good enough.
Helicoils are not hard to do, so if any of the inspections show any loosening I would go that way.
|
|
Azusa Go-Kart Live Axle Bearing Kit for 1in. Axle with 3-Hole Flangettes $42.99 Everything you need to assemble a live axle to your Go-Kart frame. Works with most axles. Each kit includes: two axle bearings with integral collar, two bearing hangers, four flangettes, four 5/16in.-18 x 3/4in. bolts with Teflon locking nuts, and two large Teflon locking nuts. U.S.A.... |
|
|
FWD Front Wheel Bearing Puller Remover Installer Tool $159.99 A great tool used to replace front wheel bearing without removing the steering knuckle & strut assembly. As the spindle assemble isn't removed there is no need to align front end after the job is done. Bearing Cap Size : 2 1/8", 2 5/16", 2 1/2", 2 5/8", 2 3/4", 2 7/8", 3". Bearing Outer Size : 3". Barrel Cap Inner Size : 3" and 3 1/4".... |
|
|
Azusa Steel Go-Kart Axle - 36in. Length $49.99 Full length 1/4in. keyways with stubs at axle ends. For fixed or live axles. Has 1in. dia. step down at end to 3/4in., 2in. ends with 3/4in. x 16 threads. U.S.A.... |
|
|
E-Z-Go Electric Spindle 6 Lift Kit 2001+ TXT $195.00 Lift Kits - 6" Lift Kit - For electric carts - Years 2001+ - Steering column has 4 bolts to floorboard - Tire s... |
|
|
OTC 6601 Rear Axle Nut Wrench for Ford $36.99 4-lug socket Same as Ford No. 205-448 Use with a 1/2” Drive ratchet or breaker barApplications: 2003 - newer Ford F-250, F-350, and F-450 super-duty trucks with 10-1/2” rear axle.... |